Nissan Sentra B18 (2020-2025) Service Manual: P0123 Tp Sensor

Nissan Sentra B18 (2020-2025) Service Manual / Engine / Work Procedure (After Replacing Electric Throttle Control Actuator) / Dtc/circuit Diagnosis / P0123 Tp Sensor

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC	CONSULT screen terms (Trouble diagnosis content)	DTC detection condition
P0123	TP SEN 2/CIRC-B1 (Throttle/Pedal position sensor/switch “A” circuit high)	Diagnosis condition	Engine running at idle
		Signal (terminal)	TP sensor 2 signal
		Threshold	An excessively high voltage from the TP sensor 2 is sent to ECM
		Diagnosis delay time	—

POSSIBLE CAUSE

Harness or connectors (TP sensor 2 circuit is open or shorted.)
Electric throttle control actuator (TP sensor 2)

FAIL-SAFE

Engine Control System

Engine operating condition in fail-safe mode
Device fix mode	This mode fixes the electric IVT motor and the EVT control solenoid valve in the reference position. The intake manifold runner control valve motor is turned OFF (intake manifold runner control valve opens).
Others	The ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle position to be within +10 degrees. The ECM regulates the opening speed of the throttle valve to be slower than the normal condition. So, the acceleration will be poor.

Engine operating condition in fail-safe mode

Fail safe mode

Nissan Sentra Vehicle behavior

Device fix mode

This mode fixes the electric IVT motor and the EVT control solenoid valve in the reference position.
The intake manifold runner control valve motor is turned OFF (intake manifold runner control valve opens).

Others

The ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle position to be within +10 degrees.

The ECM regulates the opening speed of the throttle valve to be slower than the normal condition. So, the acceleration will be poor.

Idle Start/Stop System

When a DTC is detected, the start/stop indicator lamp blinks slowly and the idle start/stop system operation is prohibited.

When ECM detects error while operating the idle start/stop system, ECM restarts the engine.

Confirmation Procedure

Confirmation Procedure

CHECK DTC PRIORITY

If DTC P0122 or P0123 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

Is applicable DTC detected?
YES >>
Perform diagnosis of applicable. Refer to DTC Description.
NO >>
GO TO 2.
PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 8 V or more at idle.

>>
GO TO 3.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine and let it idle for 1 second.
2. Check DTC.
Is DTC detected?
YES >>
Proceed to DTC Diagnosis Procedure.
NO-1 >>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2 >>
Confirmation after repair: INSPECTION END

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P0122 or P0123 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

Is applicable DTC detected?
YES >>
Perform diagnosis of applicable. Refer to DTC Description.
NO >>
GO TO 2.

CHECK THROTTLE POSITION (TP) SENSOR 2 POWER SUPPLY-1

Turn ignition switch OFF.
Disconnect electric throttle control actuator harness connector.
Turn ignition switch ON.

Check the voltage between electric throttle control actuator harness connector terminals.

Electric throttle control actuator	Voltage (Approx.)
F7	3	2	5 V

Electric throttle control actuator

Voltage

(Approx.)

Connector

−

Terminal

5 V

Is the inspection result normal?

YES >>

GO TO 7.

NO >>

GO TO 3.

CHECK TP SENSOR 2 POWER SUPPLY-2

Check the voltage between electric throttle control actuator harness connector and ground.

+	−	Voltage (Approx.)
F7	3	Ground	5 V

−

Voltage

(Approx.)

Electric throttle control actuator

Connector

Terminal

Ground

5 V

Is the inspection result normal?

YES >>

GO TO 5.

NO >>

GO TO 4.

CHECK TP SENSOR 2 POWER SUPPLY CIRCUIT

Turn ignition switch OFF.
Disconnect ECM harness connector.

Check the continuity between electric throttle control actuator harness connector and ECM harness connector.

Electric throttle control actuator		ECM		Continuity
Connector	Terminal	Connector	Terminal	Continuity
F7	3	F25	95	Existed

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES >>

Perform the trouble diagnosis for ECM power supply circuit. Refer to Diagnosis Procedure.

NO >>

Repair or replace malfunctioning part.

CHECK TP SENSOR 2 GROUND CIRCUIT

Turn ignition switch OFF.
Disconnect ECM harness connector.

Check the continuity between electric throttle control actuator harness connector and ECM harness connector.

Electric throttle control actuator		ECM		Continuity
Connector	Terminal	Connector	Terminal	Continuity
F7	2	F25	90	Existed

Also check harness for short to power.

Is the inspection result normal?

YES >>

GO TO 6.

NO >>

Repair or replace malfunctioning part.

CHECK ECM GROUND CIRCUIT

Check the continuity between ECM harness connector and ground.

ECM		—	Continuity
Connector	Terminal	—	Continuity
F24	5	Ground	Existed
F24	65
F25	69
E16	157
	159
	162

Also check harness for short to power.

Is the inspection result normal?

YES >>

INSPECTION END

NO >>

Repair or replace malfunctioning part.

CHECK THROTTLE POSITION SENSOR

Refer to Component Inspection.

Is the inspection result normal?
YES >>
INSPECTION END
NO >>
Replace electric throttle control actuator. Refer to Removal and Installation.

P0122 Tp Sensor

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble ...

P0125 Ect Sensor

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble ...

Other materials:

Dtc Description
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition ...

P1225 TP Sensor
DTC Logic DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition Possible cause P1225 CTP LEARNING-B1 (Closed throttle position learning bank 1) Closed throttle position learning value is excessively low. E ...

Can communication circuit
Diagnosis procedure 1.Connector inspection Turn the ignition switch off. Disconnect the battery cable from the negative terminal. Disconnect all the unit connectors on CAN communication system. Check terminals and connectors for damage, bend and loose connection. Is the inspection resu ...