Nissan Sentra manuals

Toyota Camry Owner's Manual (2023): Driving in vehicle-to-vehicle distance control mode - Dynamic radar cruise control with full-speed range

Toyota Camry Owner's Manual (2023) / Driving / Using the driving support systems / Driving in vehicle-to-vehicle distance control mode - Dynamic radar cruise control with full-speed range

This mode employs a radar to detect the presence of vehicles up to approximately 328 ft. (100 m) ahead, determines the current vehicle-to-vehicle following distance, and operates to maintain a suitable following distance from the vehicle ahead. The desired vehicle-to-vehicle distance can also be set by operating the vehicle-to-vehicle distance switch.

When driving on downhill slopes, the vehicle-to-vehicle distance may become shorter.

Using the driving support systems

  1. Example of constant speed cruising
    When there are no vehicles ahead
    The vehicle travels at the speed set by the driver.
  2. Example of deceleration cruising and follow-up cruising
    When a preceding vehicle driving slower than the set speed appears

When a vehicle is detected running ahead of you, the system automatically decelerates your vehicle. When a greater reduction in vehicle speed is necessary, the system applies the brakes (the stop lights will come on at this time). The system will respond to changes in the speed of the vehicle ahead in order to maintain the vehicle-to-vehicle distance set by the driver.

Approach warning warns you when the system cannot decelerate sufficiently to prevent your vehicle from closing in on the vehicle ahead.

When the vehicle ahead of you stops, your vehicle will also stop (vehicle is stopped by system control). After the vehicle ahead starts off, pressing the "+ RES" switch or depressing the accelerator pedal (start-off operation) will resume follow-up cruising. If the start-off operation is not performed, system control continues to keep your vehicle stopped.

When the turn signal lever is operated and your vehicle moves to an overtaking lane while driving at 50 mph (80 km/h) or more, the vehicle will accelerate to help to overtake a passing vehicle.

The system's identification of what is an overtaking lane may be determined solely based on the location of the steering wheel in the vehicle (left side driver position versus right side driver position.) If the vehicle is driven to a region where the overtaking lane is on a different side from where the vehicle is normally driven, the vehicle may accelerate when the turn signal lever is operated in the opposite direction to the overtaking lane (e.g., if the driver normally operates the vehicle in a region where the overtaking lane is to the right but then drives to a region where the overtaking lane is to the left, the vehicle may accelerate when the right turn signal is activated).

  1. Example of acceleration
    When there are no longer any preceding vehicles driving slower than the set speed
    The system accelerates until the set speed is reached. The system then returns to constant speed cruising.

Setting the vehicle speed (vehicle-to-vehicle distance control mode)

1. Press the cruise control main switch to activate the cruise control.

Dynamic radar cruise control indicator will come on and a message will be displayed on the multi-information display.

Press the switch again to deactivate the cruise control.

If the cruise control main switch is pressed and held for 1.5 seconds or more, the system turns on in constant speed control mode.

Using the driving support systems

2. Accelerate or decelerate, with accelerator pedal operation, to the desired vehicle speed (at or above approximately 20 mph [30 km/h] ) and press the "- SET" switch to set the speed.

Cruise control "SET" indicator will come on.

The vehicle speed at the moment the switch is released becomes the set speed.

Using the driving support systems

Dynamic radar cruise control with full-speed range
Summary of functions In vehicle-to-vehicle distance control mode, the vehicle automatically accelerates, decelerates and stops to match the speed changes of the preceding vehicle even if the accele ...

Adjusting the set speed - Dynamic radar cruise control with full-speed range
Adjusting the set speed by the switch To change the set speed, press the "+ RES" or "- SET" switch until the desired set speed is displayed. Increases the speed (Except when the vehicle h ...

Other materials:

U1000 can comm circuit
Dtc logic Dtc detection logic Dtc Consult Detection condition Possible malfunction location U1000 Can comm circ [u1000] When combination meter is not receiving can communication signals for 2 seconds or more. Combination meter Diagnosis procedure 1.Ch ...

Overdrive control switch
Component Function Check 1.CHECK SPORT INDICATOR LAMP FUNCTION Check OD OFF indicator lamp turns ON for approx. 2 seconds when ignition switch turns ON. Is the inspection result normal? YES >> GO TO 2. NO >> Go to TM-239, "Diagnosis Procedure". 2.CHECK SPORT MODE SW ...

Engine coolant
The coolant level is satisfactory if it is between the "F" and "L" lines on the reservoir when the engine is cold. Reservoir cap "F" line "L" line If the level is on or below the "L" line, add coolant up to the "F" line. ■Coolant selection Only use "Toyota Super Long Life Coolant" ...

© 2014-2023 Copyright www.nisentra.com