Dtc Description

DTC Description

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Harness, fuse, or connectors

• Heated seat LH low relay

• A/C auto amp. (with auto A/C)

• A/C amp. (with manual A/C)

FAIL-SAFE

—

Dtc Confirmation Procedure

DTC Confirmation Procedure

1. PERFORM DTC CONFIRMATION PROCEDURE

   1. CONSULT

      1. Ignition switch ON.

      2. Turn heated seat switch LH (LOW) ON.

      3. Select “Self Diagnostic Result” mode of “HVAC”.

   Is B24AF–14 detected?

   YES >>

   Refer to DTC Diagnosis Procedure.

   NO >>

   To check malfunction symptom before repair: Refer to Intermittent Incident.

   NO >>

   Confirmation after repair: Inspection End.

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

1. CHECK FUSE

   1. 1. Ignition switch OFF.

      2. Check that the following fuse is not blown (open):

         Signal name	Fuse No.	Capacity
         Ignition switch ON power supply	6	10 A

   Is the inspection result normal?

   YES>>

   GO TO 2

   NO>>

   Replace the blown fuse after repairing the affected circuit.

2. CHECK HEATED SEAT LH LOW RELAY POWER SUPPLY

   1. 1. Disconnect heated seat LH low relay connector.

      2. Ignition switch ON.

      3. Check voltage between heated seat LH low relay harness connector and ground.

         (+)		(-)	Voltage (Approx.)
         Heated seat LH low relay
         Connector	Terminal
         M6	1	Ground	Battery voltage

   Is the inspection result normal?

   YES>>

   GO TO 3.

   NO>>

   Repair or replace harness.

3. CHECK HEATED SEAT LH LOW RELAY

   1. Check heated seat LH low relay.

      Refer to Component Inspection.

   Is the inspection result normal?

   YES>>

   GO TO 4.

   NO>>

   Replace heated seat LH low relay.

4. CHECK HEATED SEAT LH LOW RELAY CONTROL SIGNAL

   1. 1. Connect heated seat LH low relay connector.

      2. Check voltage between A/C auto amp. (with auto A/C) or A/C amp. (with manual A/C) harness connector and ground.

         With auto A/C

         (+)		(–)	Condition		Voltage (Approx.)
         A/C auto amp.
         Connector	Terminal
         M34	75	Ground	Heated seat switch LH (LOW)	OFF	Battery voltage
         				ON	0 V

         With manual A/C

         (+)		(–)	Condition		Voltage (Approx.)
         A/C amp.
         Connector	Terminal
         M82	75	Ground	Heated seat switch LH (LOW)	OFF	Battery voltage
         				ON	0 V

   Is the inspection result normal?

   YES>>

   Replace A/C auto amp. (with auto A/C) or A/C amp. (with manual A/C). Refer to Removal and Installation (with auto A/C) or Removal and Installation (with manual A/C).

   NO>>

   GO TO 5.

5. CHECK HEATED SEAT LH LOW RELAY CONTROL SIGNAL CIRCUIT

   1. 1. Ignition switch OFF.

      2. Disconnect A/C auto amp. connector (with auto A/C) or A/C. amp. connector (with manual A/C) and heated seat LH low relay connector.

      3. Check continuity between A/C auto amp. harness connector (with auto A/C) or A/C. amp. harness connector (with manual A/C) and heated seat LH low relay harness connector.

         With auto A/C

         A/C auto amp.		Heated seat LH low relay		Continuity
         Connector	Terminal	Connector	Terminal
         M34	75	M6	2	Yes

         With manual A/C

         A/C amp.		Heated seat LH low relay		Continuity
         Connector	Terminal	Connector	Terminal
         M82	75	M6	2	Yes

      4. Check continuity between A/C auto amp. harness connector (with auto A/C) or A/C amp. harness connector (with manual A/C) and ground.

         With auto A/C

         A/C auto amp.		(–)	Continuity
         Connector	Terminal
         M34	75	Ground	No

         With manual A/C

         A/C amp.		(–)	Continuity
         Connector	Terminal
         M82	75	Ground	No

   Is the inspection result normal?

   YES>>

   GO TO 6.

   NO>>

   Repair or replace harness.

6. CHECK INTERMITTENT INCIDENT

   1. Check intermittent incident.

      Refer to Intermittent Incident.

   >>

   Inspection End.