S Nissan Sentra Manuals Library
Factory-style information for owners and repair work

Nissan Sentra techinfo

Find Nissan Sentra owner information, maintenance instructions, technical references, service procedures and useful repair pages in one clean online library.

Quick access Sentra Docs
B18 Owner's 2020-2025 Sentra owner information B18 Service 2020-2025 Sentra Workshop manual B17 Owner's 2013-2019 Sentra owner documentation B17 Service 2013-2019 Sentra service information

Nissan Sentra B18 (2020-2025) Service Manual: B0012-09 Active Vent

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)

DTC Detection Condition

B0012–09

ACTIVE VENT

[SHORT]

Diagnosis condition

When ignition switch is ON.

Signal (terminal)

Active vent circuit is shorted to each other (terminals 41 and 42).

Threshold

—

Diagnosis delay time

—

POSSIBLE CAUSE

[SHORT]

  • Connection malfunction or short circuit of harness and connector

  • Internal malfunction of front passenger air bag module (active vent)

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

  1. CHECK SELF DIAGNOSTIC RESULT

    1. CONSULT

      1. Ignition switch ON.

      2. Select "Self Diagnostic Result" mode of "AIR BAG".

      3. Check for DTC.

    Is the DTC detected?

    YES>>

    (Current DTC) Refer to DTC Diagnosis Procedure.

    YES>>

    (Past DTC) GO TO 2.

    NO>>

    Inspection End.

  2. ERASE SELF DIAGNOSTIC RESULT

    1. CONSULT

      Erase the DTC.

    Can the DTC be erased?

    YES>>

    Inspection End.

    NO>>

    Refer to DTC Diagnosis Procedure.

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

Warning:

  • Before servicing, ignition switch OFF, disconnect battery negative terminal, and wait at least 3 minutes or more (to discharge backup capacitor).

  • Never use an unspecified tester or other measuring device.

  1. HARNESS CONNECTOR

    1. Visually inspect all applicable harness connectors for the following:

      • Visible damage to connector or terminal

      • Loose terminal

      • Poor connection

        Note:

        All harness connectors should be inspected from the air bag diagnosis sensor unit to the end component (including any in-line connectors).

    Is the inspection result normal?

    YES >>

    GO TO 2.

    NO >>

    Perform one of the following repairs:

    • Visible damage: Replace the harness.

    • Loose terminal: Secure the terminal.

    • Poor connection: Secure the connection.

  2. CONFIRM DTC

    1. CONSULT

      1. Reconnect all harness connectors.

      2. Ignition switch ON.

      3. Select "Self Diagnostic Result" mode of "AIR BAG".

      4. Check for DTC.

    Is DTC still current?

    YES >>

    GO TO 3.

    NO >>

    Refer to Intermittent Incident.

  3. WIRING HARNESS

    1. Check the wiring harness for visible damage.

      Note:

      The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component (including any in-line connectors).

    Is the inspection result normal?

    YES >>

    GO TO 4.

    NO >>

    Replace the harness.

  4. CONFIRM DTC

    1. CONSULT

      1. Reconnect all harness connectors.

      2. Ignition switch ON.

      3. Select "Self Diagnostic Result" mode of "AIR BAG".

      4. Check for DTC.

    Is DTC still current?

    YES >>

    GO TO 5.

    NO >>

    Refer to Intermittent Incident.

  5. FRONT PASSENGER AIR BAG MODULE

    1. CONSULT

      1. Replace the front passenger air bag module. Refer to Removal and Installation.

      2. Ignition switch ON.

      3. Select "Self Diagnostic Result" mode of "AIR BAG".

      4. Check for DTC.

    Is DTC still current?

    YES >>

    GO TO 6.

    NO >>

    Clear DTC. Inspection End.

  6. AIR BAG DIAGNOSIS SENSOR UNIT

    1. CONSULT

      1. Replace the air bag diagnosis sensor unit. Refer to Removal and Installation.

      2. Ignition switch ON.

      3. Select "Self Diagnostic Result" mode of "AIR BAG".

      4. Check for DTC.

    Is DTC still current?

    YES >>

    GO TO 7.

    NO >>

    Clear DTC. Inspection End.

  7. RELATED HARNESS

    1. Replace the related harness.

    >>

    Inspection End.

    B0002-09 Driver Air Bag Module
    Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition B0002–09 DRIVER AIR BAG MODULE 2 [SHORT] D...
    B0012-55 Active Vent
    Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B0012-55 ACTIVE VENT [NOT CONFIGURED] Diagno...

    Other materials:

    Work Procedure (Before Replacing Electric Throttle Control Actuator)
    CHECK DTC Perform DTC P0101 confirmation procedure. Refer to Confirmation Procedure. Is the DTC P0101 displayed? YES >> GO TO 2. NO >> Replace electric throttle control actuator. Refer to Removal and ...

    Wiper & Washer. Preparation. Preparation. Special Service Tools
    Preparation. Special Service Tools Special Service Tools Special Service Tools The actual shape of the tools may differ from those illustrated here. Tool number (TechMate No.) Tool name &nbs ...

    C1732-16 Tire Pressure Sensor Fr
    Dtc Description DTC Description Note: The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information. Activate and display TPMS sensor IDs Display tire pressure rep ...